|Rongda Industrial Park, Xinhua Road, Wangting Town, Suzhou City, China|
|Place of Origin:||Jiangsu,China|
|Minimum Order Quantity:||Negotiable|
|Packaging Details:||bulk packing, small box packing, packing as required|
|Delivery Time:||20-30 working days|
|Payment Terms:||T/T, L/C, D/P|
|Supply Ability:||200 ton per month|
|Name:||Nylon Nail-in Anchor||Colour:||Yellow, Gray, Red|
|Material:||Nylon PA And PE, Plastic||Thread:||Full Thread, Half Thread|
|Packing:||Bulk Packing, Small Box Packing, Plastic Bag Packing||Head Type:||Flat Head, Round Head, Mushroom Head|
nylon hammer drive anchor,
nylon sleeve frame fixing anchor
Flat Countersunk Head Insulation Nylon Hammer Drive Anchor For Wood Home Depot
1. Name: nylon hammer anchor nail screw, nylon hammer fixing anchor
2. Grade: C10B21, C1022, SUS201,SUS410,SUS304,SUS316,A2-70,A2-80,A4-80
3. Diameter: M5-M10
4. Length: From 30mm to 220mm
5. Certification: ISO9001, SGS, CTI, ROHS
3. Production Feasures:
|Description||A fastening system which consists of two parts: (1) a nylon piece similar in design to a blind rivet which has a cylindrical shank spliton two sides, 180° apart, extending from the bottom of the shank up most of the distance to the head. The shank has several ribs extending completely around its circumference. Mushroom, pan and flat head styles are available; (2) a steel pin expander which passes through a concentric channel extending from an opening in the top of the head of the nylon piece down into the shank to a point just below the spot where the split ends below the head. The pin has a slot across the top of its head, a chiseled point similar to a nail, and threads on its own shank which helps to lock the anchor in place upon installation.|
|Installation is achieved by inserting the end of the nylon shank into a pre-drilled hole and hammering the head of the nail until it meets the head of the anchor body. Driving the nail through the body expands the split ends which allows the ribs to grip the wall of the prepared hole. This is a light duty anchor for use in solid materials such as concrete, brick and block, preferred when fixtures must be attached without chipping the fixture or the masonry. Can also be used like a toggle bolt in wallboard or plaster, or as a
blind rivet in joining several thicknesses of material together, especially in applications subject to vibration. The nylon withstands temperatures from -40°F to 170°F
|Material||Body: Injection molded thermoplastic nylon Expander Pin: AISI 1018-1021 or equivalent cold rolled steel, zinc plated|
|Anchor Spacing||Anchors should be spaced 18-24 inches apart (measured from the center of the anchor)|
|Hole should be drilled to a depth of at least 1/4" deeper than the required embedment. Likewise,the thickness of the base material should be at least 125% of the embedment to be used.|
|Tensile Strength||Nylon nail anchors shall not be removable or show evidence of failure when subjected to axially applied proof test loads as specified in the above table when set in concrete of 3000 psi. compressive strength. The suggested safe working load is one-fourth the loads shown in the above table.|
It is available in two different diameters: 3/16” and 1/4”. The 3/16” diameter is available in lengths of 3/4”, 1”, and 1-1/2”. The 1/4” diameter is available in lengths of 1”, 1-1/2”, 2”, and 3”.
It is split to allow the anchor body to move apart as the nail is forced down into the anchor body, which creates expansion force against the base material.
Yes, it can be installed through the fixture into the concrete, and hole spotting is not necessary. Make sure that the hole in the fixture is slightly larger than the designated diameter of the anchor being installed.
How deep do I drill the hole?
The hole must be at least 1/4” deeper than the expected embedment in the base material.
Yes. Any concrete dust or debris in the hole may reduce the holding values of the anchor. Cleaning the hole will ensure a better chance for a quality fastening.
5. More pictures:
NYLON NAIL ANCHOR, PIN DRIVE ANCHORS
Contact Person: Tom